camshaft是什么意思   camshaft怎么读

camshaft单词基本解析：

camshaft变化用词：

camshaft英英释义：

1. has cams attached to it

名词 camshaft:

has cams attached to itcamshaft[ 'kæmʃɑ:ft ]n.has cams attached to it

camshaft中文词源：

camshaft用法和例句：

As camshaft rotates, the lobe, or high spot of the cam, pushes of the valve.

当凸轮轴旋转时, 凸轮凸起的或者高点的位置, 推动气门座.

Angular velocity grinding and linear velocity grinding are the main grinding method for camshaft.

工件恒角速度磨削和工件恒线速度磨削是目前精加工凸轮轴的主要磨削加工工艺.

In this paper, the theory of cam profiling by CNC swing type camshaft grinder is analyzed.

详细分析了摇架式凸轮轴磨床凸轮轮廓的数控成形原理.

These engines are known as dual overhead camshaft ( DOHC ) engines.

这些发动机被称为双顶置凸轮轴 ( DOHC ) 发动机.

The ratio of the crankshaft to the revolutions of the camshaft is 2∶1.

曲轴的转速与凸轮轴的转速之比是2∶1.

The metal shaft, called the camshaft, typically has individual cams for each valve in the engine.

那金属轴叫凸轮轴, 在发动机里的每个气门一般有各自的凸轮.

Remove the camshaft retaining bolt and remove the sprockets and chain as an assembly.

拆去凸轮轴固定螺栓,并拆去作为一个总成的链轮和链条.

A camshaft driven by a chain or belt turns in the same direction as the crankshaft.

凸轮轴被链或者带驱动,使其朝着曲轴相同的方向转动.

The camshaft has a cam, on which there is a lob , or bump.

凸轮轴上有一个凸轮, 凸轮上有一个凸角.

A formula of the camshaft rotating velocity is deduced while keeping constant metal removal rate.

推导出了保持磨除率基本恒定时,数控凸轮轴磨床磨削凸轮时凸轮轴转速变化的计算公式.

The opening of each valve is controlled by a camshaft.

每个阀门的开启由凸轮轴控制.

The manganate phosphating technology of camshaft is introduced.

介绍凸轮轴的磷化工艺.

This is called an overhead camshaft arrangement.

这被叫为顶置凸轮轴装置.

Since 1958, an engine with a single overhead camshaft has been used.

从1958年起, 便已使用带有单顶置凸轮机的发动机.

辞典例句

The influence of inoculant addition amount on the structure and properties of camshaft was investigated.

试验了孕育剂量对凸轮轴组织和性能的影响.

The camshaft and crankshaft gears can be connected directly, or meshed.

凸轮轴和曲轴齿轮可能被直接连结, 或者相啮合.

Upward camshaft; chain transmission; timing gas distribution system is stable and has little noise.

顶置凸轮, 链条传动, 正时配气系统传动平稳,噪音小.

The front timing cover and and a finished camshaft with timing gear on the end.

前面的时间和范围,并完成与凸轮轴齿轮的时间就结束.

This means that the crankshaft will make two revolutions for every revolution of the camshaft.

这意味着凸轮轴每旋转一次曲轴将旋转两次.

Two TDC ( Top Dead Center ) sensors are mounted at the rear of the single camshaft.

两个上死点的传感器安装在凸轮轴的后面.

The isothermal quenching process of the ductile iron camshaft was analyzed.

对球铁凸轮轴的等温淬火工艺进行了分析.

The camshaft rotates in phase with the crankshaft, but at half its speed.

凸轮轴和曲轴协调旋转, 但速度仅是曲轴的一半.

《简明英汉词典》

Argon arc remelting hardening is a new technology of manufacturing camshaft.

氩弧重熔硬化是生产凸轮轴新工艺.

camshaft

The front end of the crankshaft carries three devices.the gear or sprocket that drives the camshaft,the vibration damper.and the fan belt pulley.The pulley drives the engine fan,water pump,and generator with a V belt.

"在曲轴的前端有三个装置:驱动凸轮轴的齿轮或链轮、减震器和风扇皮带轮。皮带轮通过V型皮带驱动发动机风扇,水泵和发电机。"

Description: Wenzhou TOBA Auto Parts Co.,Ltd ---- TOBA specializes in manufacturing water pump,fan clutch,oil pump and camshaft both for passenger cars and heavy duty trucks.

------专业制造乘用车及卡车用冷却水泵、机油泵、硅油离合器及凸轮轴。

Description: Jiangxi Tongxin Machinery Manufacturing Co.,Ltd ---- Engine camshaft,fuel pump,camshaft,diesel engine,camshaft.

------汽车发动机凸轮轴、油泵凸轮轴、柴油机凸轮轴等。

The Parametric Design of Camshaft with CATIA V5

5环境下的凸轮轴参数化设计

The value-opening mechanism includes a valve lifter and a cam on a camshaft

一套气门开启机构包括一个气门挺杆和一个在凸轮轴上的凸轮。

A new type of variable camshaft timing system (VCT) on the V8 engine introduces another industry first.

一种新型的可变凸轮轴正时系统（自愿咨询和检验）的V8引擎引入了另一个行业第一。

It is not advisable to attempt to replace camshaft bearings unless special removal and installation tools are available.

不要试图更换凸轮轴轴承，除非能够使用特殊的拆卸和安装工具。

Two TDC (Top Dead Center) sensors are mounted at the rear of the single camshaft.

两个上死点的传感器安装在凸轮轴的后面。

In order to achieve such performance data, the engine camshaft, cylinder components, and so on have done a special reinforcement, into the exhaust system is optimized to deal with.

为了达到这样的数据表现，发动机的凸轮轴、汽缸等部件都做了特别加固，进、排气系统也进行了优化处理。

A system of automated NC camshaft grinding machine with moderate price and high capability was developed.

为此,开发了一套价格适中的高性能数控凸轮磨床控制系统。

Such auto accessories as piston ring, car bridge, steel ring, piston, camshaft and spring are of high quality nation wide.

为汽车配套的活塞环、车桥、钢圈、活塞、凸轮轴、弹力弹簧等产品在全国同行中占有一定的地位。

The main products are as follows, exhaust manifold, bent axle, camshaft, rubbing sassafras nestification, gearbox, support, flywheel, etc.

主要产品有：排气歧管、曲轴、凸轮轴、摩擦嵌套、变速箱、支架、飞轮等。

The paper presents the vibration timing effect process used on engine block of 16V280ZJ diesel engine. The correctness of the process is validated by measuring scanned curve and coaxiality of main shaft bore and camshaft bore.

介绍了 16 V2 80 ZJ型柴油机机体振动时效的工艺 ,通过扫频曲线和主轴孔、凸轮轴孔同轴度的测量验证了采用该工艺的正确性。

The manganate phosphating technology of camshaft is introduced.

介绍凸轮轴的磷化工艺。

The paper introduces the application of the digital regulator combiningcomplex control with PD control to DC servo system of cam prefile shaping of the NCgrinder of camshaft.

介绍复合控制与PD控制相结合的数字调节器在数控凸轮轴磨床凸轮轮廓成形直流伺服系统中的应用。

The sedan camshafts re-melting and chilling process and production technique of shell mold camshaft castings to be re-melted and chilled were introduced.

介绍重熔淬火硬化处理凸轮轴工艺,以及供重熔淬火用的壳型凸轮轴的生产工艺。

Since 1958, an engine with a single overhead camshaft has been used

从1958年起，便已使用带有单顶置凸轮机的发动机。

But a camshaft driven directly by the crankshaft gear turns in the opposite direction.

但是凸轮轴被曲轴齿轮直接驱动，其将在相反方向上转动。

Production Technique of Low Alloy Chilled Cast Iron Camshaft

低合金冷激铸铁凸轮轴的生产技术

Practical Production of Camshaft of Quenchable Low Alloy Cast iron

低合金可淬硬铸铁凸轮轴的生产实践

Keywords eccentric camshaft;cold extrusion;warm extrusion;extrusion die;

偏心凸轮轴;冷挤压;温挤压;挤压模具;

The eccentric may be part of the camshaft itself or may bolt to it.

偏心轮可能与凸轮轴是一体的，也可能是通过螺钉连接的。

camshaft chain and sprocket drive

偏心轴链条传动

Crack-resistant Performance Improvement of A Chilled Gray Cast Iron Camshaft

冷激灰铸铁凸轮轴抗断裂性能的提高

Foundry Technology of Chilled Cast Iron Camshaft

冷激铸铁凸轮轴铸造技术

Impact of coarse grain of camshaft raw material on normalized structure

凸轮原材料粗晶对正火组织的影响

cam and camshaft grinding maching

凸轮和凸轮轴磨床

Keywords camshaft;longitudinal-grinding;latitudinal grinding;

凸轮轴;纵磨;横磨;

Keywords Camshaft;Casting;KBE system;Parametric design;Neural network;

凸轮轴;铸造;KBE系统;参数化设计;神经网络;

Keywords camshaft;manganate phosphating;process;

凸轮轴;锰盐磷化;工艺;

The camshaft has a cam, on which there is a lob, or bump.

凸轮轴上有一个凸轮，凸轮上有一个凸角。

The camshaft also can be located in the lower part of the engine, within the engine block.

凸轮轴也装在发动机底部的气缸体内。

Toothed rim for camshaft drive

凸轮轴传动装置齿圈

The camshaft rotates in phase with the crankshaft, but at half its speed.

凸轮轴和曲轴协调旋转, 但速度仅是曲轴的一半。

Camshaft and crankshaft grinding machines

凸轮轴和曲轴磨床

The camshaft and crankshaft gears can be connected directly, or meshed. This type of operating linkage commonly is used on older six-cylinder, inline engines.

凸轮轴和曲轴齿轮可能被直接连结，或者相啮合。这类操作联动通常被用在更老的六气缸，直列发动机上。

reamer for camshaft aligning

凸轮轴孔校正铰刀

camshaft installation guide piece

凸轮轴安装导块

There are 5 supporting journals and 8 valve cams on the camshaft.

凸轮轴有5个支承轴颈和8个配气凸轮。

Re-melding in Ar arc welding of camshaft is particular heat treatment for hardening.

凸轮轴氩弧重新熔化硬化是一独特的热处理方式。

oil pressure control valve of camshaft

凸轮轴油压控制阀

Formation Reason and Prevention of Blow Hole on Chilled Surface of Camshaft

凸轮轴激冷面气孔成因及防止方法的探讨

Automatic Measurement of Camshaft and Evaluation of Data Processing(1)

凸轮轴的自动测量及数据处理评定方法(1)

Remelt hardening technology of camshaft with tungsten inert gas arc

凸轮轴的钨极氩弧重熔淬火工艺

Study and Making of the Detecting System Determining the Position of the Camshaft Grinder's Grinding Wheel

凸轮轴磨床砂轮定位检测系统的研制

Automatic Fluorescent Magnetic Particle Testing System in Camshaft

凸轮轴荧光磁粉全自动检测系统

A camshaft driven by a chain or belt turns in the same direction as the crankshaft.

凸轮轴被链或者带驱动，使其朝着曲轴相同的方向转动。

The camshaft is geared to turn at one-half the rate of the crankshaft.

凸轮轴转动应与曲轴相配合，其速度是曲轴的一半。

Technology and Equipment of Re-Meld Hardening for Camshaft

凸轮轴重熔硬化工艺与设备

Keywords Camshaft Key Seat;Symmetry;Measurement Block;

凸轮轴键槽;对称度;测量块;

Research of Tool for Quick Measurement of Camshaft key Seat Symmetry

凸轮轴键槽对称度快速检具的研制

Renovation of Camshaft Contour Grinding Machine by Non-Contour NC Technique

凸轮轴靠模磨床的无靠模数控改造

The Approach of the Angle Measure on Gears over the Camshaft and Crankshaft

凸轮轴齿轮和曲轴齿轮正时角度检测新方法

camshaft gear timing indicator

凸轮轴齿轮定时指示器

The defect sources of camshaft remelt hardening such as surface pores,graphite floatation,edge damage,surf...

分析凸轮轴重熔淬火中主要质量缺陷产生的原因,得出提高硬化处理合格率的现场措施。

Design of the NC Special Milling Machine for Brake Camshaft

制动凸轮轴数控专用铣床设计

Odd camshaft differential reversing

单凸轮差动换向

SOHC Single Over Head Camshaft

单顶置凸轮轴

Influence of Raw Material on Struture and Property of Chilled Iron Camshaft

原材料对冷激铸铁凸轮轴组织和性能的影响

Optimizing Design of Camshaft Bearing

双列偏心满装深沟球轴承的优化设计

TC Twin Carburetor Twin Camshaft

双化油器,双凸轮轴

The Design and Study of Synchronous Belt Drives For Double Overhead Camshaft

双顶置凸轮轴正时齿形带传动系统的设计研究

Repair Method for Roundness Deformation on Rear Bering Bore of Engine Camshaft Due to Burning Erosion and Wear

发动机凸轮轴后座孔烧蚀磨损失圆的修复方法

Failure Analysis and Optimization of Sealing of Camshaft Rear Cover

发动机凸轮轴后端盖密封失效分析及优化

In addition, when the camshaft is located over the cylinder head, the arrangement is known as an overhead camshaft( OHC) design.

另外，当凸轮轴位于汽缸盖上面时，这种方式被称为是顶置凸轮轴(hc)构。

In addition, when the camshaft is located over the cylinder head, the arrangement is known as an overhead camshaft (OHC) design.

另外，当凸轮轴位于汽缸盖上面时，这种方式被称为是顶置凸轮轴(OHC)结构。

V tech variable camshaft system is free.

可變凸轮軸系統是不受限制的。

Quenchable cast iron camshaft

可淬硬铸铁凸轮轴

Keywords Quenchable cast iron camshaft;V-Ti pig iron;hardness;strength;

可淬硬铸铁凸轮轴;钒钛生铁;硬度;抗拉强度;

Supplies the required 5 volt power source to the crankshaft position sensor, camshaft position sensor, MAP sensor and throttle position sensor.

向曲轴位置感应器、凸轮轴位置感应器、MAP感应器以及节气阀位置感应器提供所需的5伏电压。

As the camshaft continues to rotate, the high spot moves way from the valve mechanism.

因为凸轮轴继续旋转，凸轮轴上的凸起部分离开气门装置。

Since the engine has no valves, it doesn't need any camshaft, valve lifters and so on.

因为发动机没有阀门，它不需要任何凸轮轴、起阀器等。

Therefore, it has been the focus for automobile industry to resolve the problem of how to check camshaft, especially how to measure the cam lift, and how to promote and stable the quality of camshaft.

因此,解决凸轮轴检测问题特别是凸轮升程测量问题,稳定和提高凸轮轴生产质量,一直是汽车生产企业关注的的重点之一。

Therefore, the camshaft must revolve at exactly half the speed of the crankshaft.

因此，凸轮轴必须以曲轴正好一半的速度旋转。

On some engines, a metal chain is used to connect the crankshaft and camshaft gears. Most push-rod engines and some OHC engines have chains.

在一些发动机上，金属链被用来连结曲轴和凸轮轴齿轮。大多数推杆发动机和一些顶置凸轮轴发动机都有链。

In the engine, oil is supplied to crankshaft and camshaft journals rotating in their supporting bearings.

在发动机里,机油被供应到旋转在其支承轴内的曲轴和凸轮轴轴颈上。

On most engines, this mechanism, called the valve train, includes a cam on the camshaft, a valve lifter, a push rod, and a rocker arm.

在大多数发动机中,这套装置叫做气门机构。这套装置中包括凸轮轴上的一个凸轮、一个气门挺杆、一个气门推杆和一个摇臂。

The Study of CNC System for Camshaft Grinder Based on PMAC

基于PMAC的凸轮轴磨床开放式数控系统研究

Camshaft Interpolation Algorithms Based on Non-uniform Rational B-spline

基于非均匀有理B样条的凸轮轴插补算法

Eliminate Ferrite Structure in the Camshaft of Shell Mould Chilled Casting

壳型铸造凸轮轴铁素体组织的消除

This is called an overhead camshaft arrangement.
这被叫为顶置凸轮轴装置。

The eccentric may be part of the camshaft itself or may bolt to it.
偏心轮可能与凸轮轴是一体的，也可能是通过螺钉连接的。