locknut单词基本解析：

n.防松螺母，对开螺母
n. 锁紧螺母
n.防松螺母，对开螺母；

locknut变化用词：

异体字: lock nut |

locknut英英释义：

Noun

1. supplementary nut that is screwed down on a primary nut to prevent it from loosening

名词 locknut:

supplementary nut that is screwed down on a primary nut to prevent it from loosening

同义词：safety nut

locknut[ 'lɔknʌt ]n.supplementary nut that is screwed down on a primary nut to prevent it from loosening

同义词：safety nut

locknut中文词源：

locknut用法和例句：

Recheck clearance again after tightening locknut . Readjust clearance as necessary.

拧紧防松螺母后,再一次检查间隙,视需要重新调节间隙.

互联网

Recheck clearance on all valves again after locknut is tightened.

防松螺母拧紧后,再对所有气门的间隙重新检查一次.

互联网

Tighten valve adjusting screw locknut to 27 N · m ( 20 lb - ft ).

将气门调节螺丝防松螺母拧紧至27牛顿·米 ( 20磅 - 尺 ).

互联网

Tighten locknut 1 to fix the thread stand.

拧紧固定螺母1不让线架装置松动.

互联网

Position locknut over top of fuel pump module.

将锁定螺帽放在燃油泵模组上.

互联网

It has locknut fasten rotor to a spindle.

配有防松螺母固定转子与中心轴.

互联网

Secure with locknut and gaskets. Install valve assembly.

用放松螺母和垫圈紧固. 安装阀门总成.

互联网

For example jersey cloth, rayon locknut and nylon tricot are made in this method.

例如紧身运动套衫面料 、 粘胶长丝经平绒针织物和尼龙经编织物都是用这种方法制成的.

互联网

The valve is mainly made up of handle, body, disc, locknut and seal etc.

手动密闭闸阀主要由把手 、 阀体 、 插板 、 锁紧螺钉、密封装置等部件组成.

互联网

The adjusting nut and the anti - fake seal fixing body are arranged on locknut through screw threads.

调整螺母、 防伪 印模固定体用螺纹安装在锁母上.

互联网

locknut

conduit locknut

[电] 制管圈

Research on a new-type intelligent locknut

一种新型智能防松螺母的研究

For locating bearing positions and CARB bearings insert a locating ring between the bearing outer ring and housing shoulder on the locknut side of bearing.

为将定位轴承和CARB轴承的位置定准,将一个定位环插放到轴承外圈和轴承座挡边之间、轴承锁紧螺母的一侧。

Use an open-end wrench and open the locknut on the accumulator valve assembly two or threefull turns.

使用开口扳手，打开蓄能器阀门上的防松螺栓-----------。

For example jersey cloth, rayon locknut and nylon tricot are made in this method. Sometimes these materials are tubular to make cutting out more economical.

例如紧身运动套衫面料、粘胶长丝经平绒针织物和尼龙经编织物都是用这种方法制成的。有时这些面料是圆筒的,裁剪时更经济,这就是针织法。

5.If valve clearance needs to be adjusted, loosen the locknut on rocker arm adjusting screw.Turn adjusting screw until feeler gauge slips with a slight drag.

如果气门间隙需要调节，松开摇臂调节螺丝上的防松螺母，转动调节螺丝直到测隙规滑动时稍带阻力为止。

wiles locknut

威尔氏销紧螺母

Position locknut over top of fuel pump module.

将锁定螺帽放在燃油泵模组上。

Keywords color kinescope;locknut;MPPO;injection mould;automatic de-threading;

彩色显像管;锁紧螺母;改性聚苯醚;注射模;自动脱螺纹;

Application of Radial Locknut in Bridge Derrick Trail

径向防松螺母在桥式起重机轨道中的应用

The valve is mainly made up of handle, body, disc, locknut and seal etc.

手动密闭闸阀主要由把手、阀体、插板、锁紧螺钉、密封装置等部件组成。

Tighten locknut 1 to fix the thread stand.

拧紧固定螺母1不让线架装置松动。

Fuel Pump Module Locknut

燃油泵模组锁定螺帽

Secure with locknut and gaskets. Install valve assembly.

用放松螺母和垫圈紧固。安装阀门总成。

Pipe-threaded for pipe connections and straight-pipe threaded for locknut

管道螺纹用于管道连接,直线管道螺纹用于防松螺母

ALMA Aircraft Locknut Manufacturers Association

美国飞机锁紧螺母制造商协会

self-tightening locknut

自紧防松螺母

A Sort of Simple Torsion Tester of Locknut

自锁螺母简易扭力试验器

Adjustment Cap Locknut

调节帽防松螺母

Adjustment Screw Locknut

调节螺钉防松螺母

Output flange is connected with output shaft by a involute spline, and fastened by a locknut.

输出突缘通过渐开线花键与输出轴相连，并用锁紧螺母将其锁住。

It has locknut fasten rotor to a spindle.

配有防松螺母固定转子与中心轴。

NUMERIC ANALYSIS OF THE ANTI-BREAKING MECHANISM OF FE-BASED SMA LOCKNUT

铁基形状记忆合金防松螺母防断机理的数值分析

locknut bearing

锁紧螺帽座

The locknut torque needed to move the washer at the maximum washer interference fit shall not exceed the torques given in Table 3.

锁紧螺母扭矩压紧垫片时，其与垫片的最大相互作用力不能超过表3所给扭矩值。

galvanized locknut

镀锌锁母

Recheck clearance on all valves again after locknut is tightened.

防松螺母拧紧后,再对所有气门的间隙重新检查一次。

13. Recheck clearance on all valves again after locknut is tightened.

防松螺母拧紧后，再对所有气门的间隙重新检查一次。

Nonmetallic six-angled locknut with component embedded

非金属嵌件六角锁紧螺母

---