flangeless是什么意思 flangeless怎么读
英式：[f'lændʒles]
美式：[f'lændʒles]
flangeless单词基本解析：
无凸缘的flangeless变化用词：
flangeless英英释义：
flangeless中文词源：
flangeless用法和例句：
flangeless
"Butterfly Valves 2""-12"" shall be of the flangeless type, both lug and wafer styles."
2至12英寸公称通径的蝶阀是无法兰类型,但都有平板型和吊耳型两种类型。
It is the latest design,using symmetric spherical roller , two pcs of pressed steel cages,flangeless inner ring & guide ring centred on the cage.
国际最新设计，对称球面滚子，两片淬火钢冲压保持架，内圈无挡边和带一个保持架引导的中挡圈。
All valves should have flanged connections. Flangeless, wafer or lugged flange style control valves shall not be used.
所有阀门宜有法兰式接口，不应使用非法兰，夹持式或耳形凸缘型调节阀。
Keywords Design of heat exchanger;structural adoption;flangeless cone;boiling device;
换热器设计;壳体结构选择;无折边锥形封头;煮沸器;
Keywords Flangeless Cylinder Tensile coefficient Affluence measure C program;
无凸缘圆筒形件;拉深系数;富裕量;C程序;
Flangeless cylindrical parts are a kind of drawing parts and widely applied in production.
无凸缘筒形件是生产中应用较为普遍的一种拉深制件。
flangeless liner
无凸缘衬筒
flangeless cone
无折边锥形封头
The detained calculation methods and steps are introduced on technology of flangeless cylindrical part.It possesses much better applicability in production and teaching.
本文主要对无凸缘筒形件拉深的工艺计算提出了较为详细的计算方法和步骤,经生产、教学实践应用,具有较好的适用性。
Style G wafer style body valves are designed with flangeless bodies with relatively short face-to-face dimensions.
类型G对夹式阀体阀门采用无法兰阀体结构，面对面尺寸相对较短。
Style G wafer style body valves are designed with flangeless bodies with relatively short face-to-face dimensions. They are clamped between mating flanges which are connected by studs and nuts.
类型G对夹式阀体阀门采用无法兰阀体结构，面对面尺寸相对较短。这种阀门夹紧在采用螺栓和螺母的配套法兰之间。
The bearings have two loose flange rings on the outer ring, a flangeless inner ring and four rows of rollers (fig 1) or eight rows of rollers (fig 2).
这些轴承外圈上有两个松配合法兰圈,还有一个不带法兰的内圈和四列滚子(图1)或八列滚子(图2)。
Using the flangeless joint in this place.
这里采用无法兰连接。
An analysis was made on the technique for drawing a flangeless cylinder component with a small side hole.Then a die combining blanking,drawing and side-punching process was developed for the forming.
通过对侧壁带一小孔无凸缘一次拉深圆筒形件的工艺分析,合理设计了1副完成落料、拉深、侧冲孔3种工序的复合模,提高了产品质量、生产效率和经济效益。