electrometer单词基本解析：

n.静电计
n. 静电计
n.静电计；

electrometer变化用词：

形容词: electrometallurgical |

electrometer英英释义：

Noun

1. meter to measure electrostatic voltage differences; draws no current from the source

名词 electrometer:

meter to measure electrostatic voltage differences; draws no current from the source

electrometer[ ,ilek'trɔmitə ]n.meter to measure electrostatic voltage differences; draws no current from the source

electrometer中文词源：

electrometer用法和例句：

The Model 6517 A Electrometer has the Alternating Polarity Method built into a test sequence.

6517A型静电计与变换极性法已被做成一个现成的测试程序.

Use an adapter to connect the BNC connector to the triax input of the electrometer.

用一个适配器把BNC连接器连到静电计的三同轴输入端.

The ohmmeter uses an internal current source and electrometer voltmeter to make the measurement.

欧姆计使用内部的电流源和静电计电压表来进行测量.

When using the electrometer ohmmeter, measurement accuracy can be affected by a variety of factors.

使用静电计欧姆计时, 测量准确度会受到各种因素的影响.

More information on the measurement procedure can be found in the instruction manual of the electrometer.

有关测量方法的更详细的信息可以在静电计的操作手册中找到.

The damping circuit may already be built into the electrometer or may be an external circuit.

衰减电路可以装在静电计的内部,也可以是一个外部电路.

I've smashed the electrometer.

我把静电计摔碎了.

Usually, this method requires two instruments: a voltage source and a picoammeter or electrometer.

通常, 这种方法需要使用两台仪器: 一台电压源和一台皮安计或静电计.

The guard terminal of the electrometer ammeter or picoammeter is the LO input terminal.

静电计安培计和皮安计的保护端为LO输入端.

Therefore, a voltmeter with high input resistance, such as an electrometer, is required.

所以需要使用具有高输入电阻的电压表, 例如静电计.

That's because when zero check is enabled, the input resistance of the electrometer is about 10 M ω.

这是因为当零点检查功能打开时, 静电计的输入电阻大约为10Mω.

This can be checked by observing the analog output of the electrometer or picoammeter with oscilloscope.

用示波器观察静电计或皮安计的模拟输出,可以对此进行检查.

electrometer

The Model 6517A Electrometer has the Alternating Polarity Method built into a test sequence.

6517A型静电计与变换极性法已被做成一个现成的测试程序。

The Model 6517A Electrometer applies the bias voltage (VTEST), measures the leakage current, then calculates the resistance of each resistor.

6517A型静电计施加偏置电压（VTEST），并测量漏电流，然后计算出每个电阻器的电阻值。

6 General Electrometer Considerations: A discussion of techniques and error sources that affect high impedance measurements in general.

6一般静电计要考虑的问题：一般性地讨论影响高阻测量的技术和误差来源。

VC type electrometer

VC型静电仪

Lippmann's capillary electrometer

[医] 李普曼氏毛细管静电计, 微量静电计

attracted disc electrometer

[电] 吸盘静电计

capillcry electrometer

[电] 毛细管静电计

gold-leaf electrometer

[电] 金箔静电计

electrometer tubp

[电] 静电计管

The Design of Three -phase Pay in Advance Electrometer

一种三相预付费卡表的设计

In general, as ZF becomes larger, the noise gain becomes larger. Refer to the electrometer's manual or specifications for the value of the feedback impedance for a particular instrument.

一般来说，ZF变大噪声增益也变大。特定仪器反馈阻抗的数值请参见该静电计的手册或技术指标。

Compared to an electrometer, the voltage noise and drift are much lower, and the current noise and drift are much higher.

与测量高源内阻电压的静电计相比，纳伏表的电压噪声和电压漂移更低一些，电流噪声和电流漂移则是静电计要更低一些。

To measure the offset current, close a specific crosspoint and use an electrometer or SMU to measure the current with everything in place except the device under test.

为了测量偏移电流，请闭合特定的交叉点，并利用一个静电计或SMU来测量电流。在测量时，除被测装置外，所有的其它设备要连接完整。

To make the measurement, a constant voltage is applied for a prede fined period, usually 60 seconds, and the resulting current is measured with a picoammeter or electrometer.

为了进行测量，在预定的时间（通常为60秒钟）内，给样品施加恒定的电压。然后，用皮安计或静电计测量产生的电流。

To avoid measurement errors, it's critical to make proper connections from the electrometer, SMU, or picoammeter to the device under test.

为了避免测量误差，关键之点在于将静电计、SMU或皮安计和被测装置进行适当的连接。

To achieve the high impedance required specially designed "electrometer" vacuum tubes, field effect transistor must be used in the input stage.

为适应高阻抗需要，仪器输入电路中须用特殊设计的静电计专用电子管、场效应晶体管。

Main Control Unit, two-channel electrometer and servo controller.

主控制器单元,带有两通道静电计和伺服控制器。

Wulf string electrometer

乌尔夫弦线静电计

Wulf electrometer

乌尔夫静电计

binant electrometer

二位电子计

The resulting current is distributed through the volume of the test sample and is measured using a picoammeter or electrometer.

产生的电流将分布在测试样品的体内，并由皮安计或静电计来测量。

The following paragraphs examine considerations that apply to all types of electrometer and SMU measurements on high resistance sources.

以下各段考察所有类型的静电计和SMU在测量高阻源时要考虑的问题。

The basic configuration for measuring capacitance with a Model 6517A Electrometer is shown in Figure 4-35.

使用6517A型静电计进行电容测量的基本配置如图4-35所示。

Using the electrometer voltmeter with a separate current source or an SMU allows the user to make a four-wire measurement and to control the amount of current through the sample.

使用带有分立的电流源的静电计电压表或SMU时，用户能够进行四线测量并控制流过样品的电流。

The basic configuration of the constant-voltage method using an electrometer or picoammeter is shown in Figure 2-30a.

使用静电计和皮安计的恒压法的基本电路配置如图2-30a所示。

When using the electrometer ohmmeter, measurement accuracy can be affected by a variety of factors.

使用静电计欧姆计时，测量准确度会受到各种因素的影响。

tilted gold-leaf electrometer

倾斜金箔静电计

Use of Voltmeter and Electrometer in Electrocircuits

关于伏特表与静电计在电路中的使用

Refer to the instrument's instruction manual for information on a particular electrometer's internal damping feature.

关于特定静电计内部衰减电路的性能，请参阅该仪器的操作手册。

ballistic electrometer

冲击静电计

The most effective method of minimizing input capacitance is to connect the electrometer, SMU, or picoammeter to the signal source with a shielded cable that is as short as possible.

减小输入电容最有效的方法是用尽可能短的屏蔽电缆将静电计、SMU或皮安计与信号源连接起来。

dynamic condenser electrometer

动态电容器式静电计

unifilar electrometer

单丝静电计

binary electrometer

双极静电计

bifilar electrometer

双线静电计

bi quardrant electrometer

双象限静电计

dual channel electrometer

双道静电计

This can be done by placing the object in a Faraday cup and measuring the charge with an electrometer.

可以把物体放在法拉第杯中，用静电计测量其电荷。

attracted disk electrometer

吸引盘式电位计

attracted-disc electrometer

吸盘式静电计

attracted dike electrometer

吸盘静电计

Therefore, it's prudent to measure the insulation resistance of the test fixtures and cables periodically with an electrometer ohmmeter to ensure their integrity.

因此谨慎的做法是定期地用静电计欧姆计来测量测试夹具和电缆的绝缘电阻，以保证其完整性。

Figure 1-18 shows the basic configuration of an alternative form of electrometer ohmmeter.

图1-18示出另一种形式的静电计欧姆计的基本电路结构。

Figure 1-26 is a block diagram of a typical digital electrometer.

图1-26为典型数字式静电计的方框图。其模拟部分与前面讨论的电路类似。

Figure 2-24 shows a protection circuit for an electrometer ammeter or picoammeter, consisting of a resistor and two diodes (1N3595).

图2-24示出静电计或皮安计的过载保护电路，其中包括一个电阻器和两个二极管（1N3595）。

Figure 2-33 shows the electrometer ohmmeter measuring a resistance (R).

图2-33示出静电计欧姆计测量电阻（R）的情况。

The coulombmeter function of the electrometer measures charge by integrating the input current.

在其输入级的反馈回路中使用了一个积分电容器。

Isolation resistance measurements are usually made by sourcing a voltage, then measuring the resulting current using an electrometer or picoammeter.

在测量隔离电阻时，通常是提供一个电压，然后利用一个静电计或皮可安培计测量形成的电流。

Portable Electrometer Based on PIC Series Singlechip

基于PIC系列单片机的便携式静电测量仪

multicellular electrometer

复室静电计 多室静电计

multiple electrometer

复式静电计 多量程静电计

Dolezalek quadrant electrometer

多尔查累克象限静电计

The development and application of the accessories of multi-channel DC electrometer

多道直流电测仪配套设备研制与应用

As illustrated in Figure 2-38, an external feedback capacitor is placed between the preamp output terminal and the HI input terminal of the electrometer.

如图2-38所示，外部反馈电容器连在前置放大器输出端和静电计的HI输入端之间。

It can be readily measured, however, with an electrometer by using the technique described in Section VI-B

它可以用静电计轻而易举地测定，其使用方法如第六节B所述。

Practically all other insulating materials have unacceptably low volume resistivity or unsatisfactory surface characteristics for electrometer use.

实际上所有其它的绝缘材料都具有比较低的体电阻率和表面电阻率，因此对于静电计的应用是不可接受和不满意的。

Millikan electrometer

密立根静电计

symmetrical electrometer

对称静电计

Connect the HI terminal of the electrometer to one end of the resistor and the HI of the voltage source to the other end.

将静电计的HI端连到电阻器的一端，将电压源的HI端连到电阻器的另一端。

Placing the electrometer in the volts mode and then enabling external feedback switches the feedback circuit from an internal network to a feedback circuit connected to the preamp output.

将静电计置于电压模式，然后打开外部反馈，就把反馈电路从内部网络切换到连在前置放大器输出端的外部反馈网络上。

differential electrometer

差动静电计 差动电位计

balanced electrometer amplifier

平衡式电测放大器

Compton electrometer

康普顿静电计

string electrometer

弦线式静电计 弦线静电计

The circuit of the electrometer when used as a voltmeter is actually as shown in Figure 2-6.

当静电计作为电压表使用时，其电路实际上如图2-6所示。

fast electrometer amplifier

快速静电放大器

fiber electrometer

悬丝静电计

thread electrometer

悬线式静电计

I've smashed the electrometer.

我把静电计摔碎了。

Therefore, a voltmeter with high input resistance, such as an electrometer, is required.

所以需要使用具有高输入电阻的电压表，例如静电计。

torsion electrometer

扭转静电计

vibrating-diaphragm electrometer

振动膜片电位计

vibrating-free electrometer

振簧(式)静电计

vibrating reed electrometer

振簧式静电计 振簧静电计

dynamic ( condenser ) electrometer

振簧静电计

oscillation capacitive electrometer

振荡电容式静电计

emanation electrometer

放射性静电计 射气静电计

digital electrometer

数字静电计

transistor vibrating-reed micro-quantity electrometer

晶体管振簧式微量静电计

More information on the measurement procedure can be found in the instruction manual of the electrometer.

有关测量方法的更详细的信息可以在静电计的操作手册中找到。

用作名词(n.)

Refer to the instrument's instruction manual for information on a particular electrometer's internal damping feature.
关于特定静电计内部衰减电路的性能，请参阅该仪器的操作手册。

Compared to an electrometer, the voltage noise and drift are much lower, and the current noise and drift are much higher.
与测量高源内阻电压的静电计相比，纳伏表的电压噪声和电压漂移更低一些，电流噪声和电流漂移则是静电计要更低一些。

---